top of page

Blower Door Numbers Explained: CFM50, ACH50, and What They Mean

A blower-door test produces numbers that can look simple—until two houses have very different sizes, an assessor mentions “50 Pascals,” or a contractor treats one reading as a complete diagnosis. For homeowners in Westchester and the Bronx, the most useful report is not just a number. It explains what was measured, how the result was normalized, where the leakage is likely occurring, and what should happen next.


The two figures you will see most often are CFM50 and ACH50. They describe related aspects of airtightness, but they are not interchangeable, and neither one directly states how much outdoor air enters during ordinary weather.


What does 50 Pascals mean?


During a blower-door test, a calibrated fan temporarily creates a pressure difference between the home and outdoors. The common reference point is 50 Pascals, written as “50 Pa.” ENERGY STAR’s home-performance glossary describes the blower door as a fan that changes indoor pressure so leakage paths become easier to measure and locate.


Fifty Pascals is a standardized test condition—not the pressure your house normally experiences all day. The controlled pressure lets an assessor compare measurements, trace leaks, and document a before-and-after change. Wind, temperature, shielding, height, and occupant behavior still affect natural infiltration after the equipment is removed.


CFM50: the measured airflow at test pressure


CFM50 means cubic feet of air per minute moving through the calibrated fan while the house is held near 50 Pa. The DOE Building America Solution Center’s enclosure-leakage guide explains that the fan flow at that pressure corresponds to leakage through the enclosure.


CFM50 is an absolute airflow number. If the same home is tested consistently before and after air sealing, a lower post-work CFM50 usually documents reduced enclosure leakage. But raw CFM50 is a poor way to compare a compact Bronx rowhouse with a large Westchester home: the larger building contains more air and more enclosure area.


ACH50: CFM50 adjusted for building volume


ACH50 means air changes per hour at the same 50 Pa test pressure. It normalizes the fan flow by the home’s conditioned volume. The standard relationship is: ACH50 = (CFM50 × 60) ÷ conditioned building volume. The factor of 60 converts cubic feet per minute to cubic feet per hour.


For an illustrative example, a home with 16,000 cubic feet of conditioned volume and a reading of 2,400 CFM50 calculates to 9 ACH50: (2,400 × 60) ÷ 16,000. That means the fan moves the equivalent of nine building volumes per hour at the test pressure. It does not mean the home naturally replaces all its air nine times every hour.


What the numbers can—and cannot—tell you


  • They can establish a repeatable airtightness baseline when the building setup, equipment and test procedure are documented.

  • They can quantify the change after air sealing or other work that affects the enclosure.

  • They cannot identify every leak location without room-by-room tracing, pressure diagnostics or supporting observations.

  • They cannot guarantee an energy-bill reduction; savings depend on fuel, weather, thermostat settings, equipment, insulation and the leaks that were actually treated.

  • They do not replace ventilation, moisture or combustion-safety evaluation when those issues are relevant.


A single number also does not tell you whether the house is “good” or “bad” without context. Existing-home goals can differ from new-construction code targets, and appropriate recommendations depend on climate, building type, occupancy, mechanical ventilation and program requirements.


Why test setup and safety matter


Accurate testing requires the assessor to define the conditioned boundary, measure or calculate volume, record baseline pressure, prepare doors and windows consistently, use calibrated equipment, and account for conditions that can affect the reading. Current BPI standards include ANSI/BPI-1100-T-2023 for home energy auditing and ANSI/BPI-1200-S-2017 for basic building analysis.


Homeowners should not imitate a blower-door test with large exhaust fans or change combustion-appliance settings. A professional procedure includes house preparation and safety controls. If there is a gas odor, carbon-monoxide alarm, active fireplace problem, or suspected venting issue, stop and contact the appropriate emergency, utility or qualified service provider.


How diagnostics turn a number into a work plan


With the fan running, an assessor can investigate leakage at attic hatches, plumbing and wiring penetrations, rim joists, dropped soffits, window trim and other pressure boundaries. A draft at a window may be local, or it may be driven by larger leakage high or low in the building; our cold-window diagnosis guide explains that distinction.


Thermal imaging can help visualize temperature patterns when conditions are suitable, but it must be interpreted with building knowledge. Read our thermal-imaging guide for that context. Duct leakage is a separate measurement from enclosure leakage; see duct-leakage testing explained before assuming one blower-door number describes the HVAC distribution system.


Five questions to ask after the test


  • What were the measured CFM50 and calculated ACH50?

  • What conditioned volume was used in the ACH50 calculation?

  • Were weather, baseline pressure and test configuration recorded?

  • Which leakage paths were verified, and which repairs should be prioritized?

  • Will planned work require post-testing or a ventilation and safety review?


ENERGY STAR describes a home performance assessment as a combination of homeowner interview, bill review, inspection, safety checks, diagnostics and prioritized recommendations. That whole-house context is what makes the blower-door result useful.


If you want documented airtightness and leakage-path guidance for a Westchester or Bronx property, review NYEA’s Blower Door Test service. Appointment details and scope should be confirmed for the specific building before work is scheduled.

Comments

Rated 0 out of 5 stars.
No ratings yet

Add a rating
bottom of page